發電機組啟動后的8個使用規范技巧，很多朋友都認為柴油發電機組正常啟動后就不用怎么照看了，其實這是不對的，因?yàn)?a href="http://m.dtcdiy.com" target="_self">柴油發電機組啟動后才是最容易出故障的時候。所以這時候也要對它進行定期的常規檢查，這樣才能保證發電機組正常工作。

下面就來看下啟動后的8個使用規范技巧

1、將開關屏上調壓選擇開關置于手動位置;

2、打開燃油開關，同時將燃油控制手柄固定在700轉/分左右的油門位置;

3、用高壓油泵開關手柄連續地手動泵油，直到有泵油阻力，噴油器發出清脆的吱聲為止;

4、將油泵開關手柄放在工作位置上，減壓閥推向減壓位置;

5、用手搖手柄或按下電啟動按鈕起動柴油機，當柴油機達到一定轉速時，把減軸迅速拉回工作位置，使柴油機點火起動;

6、柴油機起動后，將電鑰匙撥回中間位置，轉速應控制在600~700轉/分，并密切組注意機油壓力，表的指示(工作油壓值詳見各類柴油機使用說明書)，若油壓無指示，應立即停機檢查;

7、若機組低速運轉正常，可將轉速逐漸增加到1000~1200轉/分預熱運轉，當水溫 度在50~60℃，機油溫度達到45℃左右時，再將轉速增加到1500轉/分，觀察配電屏頻率表應在50赫芝左右，電壓表為380~410伏，如果電壓偏高或偏低時可調節磁場變阻器;

8、若機組工作正常，可合上發電機與負栽間的空氣開關，然后逐漸增加負栽，向外送電;

溫馨提示大家，1、各類柴油機起動應按其柴油機使用維護說明書要求進行，2、在調壓時如機組存放過久，發電機失磁，電壓建立不起來，此時可用蓄電池充磁，充磁時磁場繞組L1(+)接蓄電池正極L2(-)接蓄電池負極，切不可接錯，3、若按下按鈕10秒，不能點火起動，應等一分鐘左右再作第二次起動，若連續三次失敗，應查明故障原因再行起動。

上述就是關于發電機組啟動后的8個使用規范技巧的介紹，注意這些使用規范，不僅能讓柴油發電機組更好的工作，同時對延長柴油發電機組壽命也很有幫助。

8 tips for using a diesel generator set after starting up. Many people believe that after a diesel generator set starts up normally, there is no need to take care of it. However, this is not true because it is the easiest time for a diesel generator set to malfunction. So it is also necessary to conduct regular inspections at this time to ensure the normal operation of the generator set.

Let's take a look at 8 usage guidelines after startup

1. Place the voltage selection switch on the switch screen in the manual position;

2. Turn on the fuel switch and fix the fuel control lever at the throttle position of around 700 revolutions per minute;

3. Use the high-pressure oil pump switch handle to manually pump oil continuously until there is pump resistance and the fuel injector makes a crisp creaking sound;

4. Place the oil pump switch handle in the working position and push the pressure reducing valve to the pressure reducing position;

5. Start the diesel engine with a hand crank or by pressing the electric start button. When the diesel engine reaches a certain speed, quickly pull the reduction shaft back to the working position to ignite and start the diesel engine;

6. After starting the diesel engine, turn the electric key back to the middle position, and the speed should be controlled at 600-700 revolutions per minute. Pay close attention to the oil pressure and the indication on the gauge (see various diesel engine manuals for the working oil pressure value). If there is no indication of oil pressure, stop the machine immediately for inspection;

7. If the unit operates normally at low speed, the speed can be gradually increased to 1000-1200 revolutions per minute for preheating operation. When the water temperature is between 50-60 ℃ and the oil temperature reaches around 45 ℃, the speed can be increased to 1500 revolutions per minute. The frequency meter on the distribution screen should be around 50 Hz, and the voltage meter should be 380-410 volts. If the voltage is too high or too low, the magnetic field variable resistor can be adjusted;

8. If the unit is working normally, the air switch between the generator and the negative load can be closed, and then the negative load can be gradually increased to transmit power to the outside;

Kind reminder to everyone: 1. All types of diesel engines should be started according to the requirements of their diesel engine maintenance manual. 2. If the unit is stored for too long during voltage regulation, the generator will lose magnetism and the voltage cannot be established. At this time, the battery can be used for magnetization. When magnetizing, the magnetic field winding L1 (+) should be connected to the positive pole of the battery and L2 (-) should be connected to the negative pole of the battery, and must not be connected incorrectly. 3. If the button is pressed for 10 seconds and the ignition cannot be started, wait for about one minute before starting again. If it fails three times in a row, the cause of the fault should be identified before starting again.

The above is an introduction to the 8 usage guidelines and techniques for starting a generator set. Paying attention to these usage guidelines can not only improve the performance of diesel generator sets, but also help extend their lifespan.